Thermic electromotive force and allowable error at 200 mv 200熱電動勢及允差mv
Thermic electromotive force and allowable error at 100 mv 100熱電動勢及允差mv
Allowable error for judge of quality testing results in feeds 飼料檢測結果判定的允許誤差
1 . thermic electromotive force and allowable error 1 .熱電動勢及允差值
Analysis of error sensitivity and allowable error of optical film , and computer controll in production 光學薄膜的誤差允差分析及生產過程中的計算機控制
The best parameters , precision grades and allowable errors of the transmission parts can be obtained by optimization to let the actuators meet the performance , technology and economy requirements simultaneously 根據傳動精度指標,最佳地規定和分配各傳動零件參數、精度等級及公差值,使之滿足設計、工藝要求。
It is also shown that the allowable errors for section dimension are loose and the allowable errors for axis line deviations are suitable in the " code for acceptance of constructional quality of concrect structures " ( gb50204 - 2002 ) . in the fifth chapter : the conclusion and the outlook 統計分析表明, 《混凝土結構工程施工質量驗收規范》 ( gb50204 - 2002 )中關于結構截面尺寸的允許偏差是較寬松的,而對軸線位移的允許偏差基本是合理的。
Arranging velocity and acceleration sensors simultaneously in the same station , in the identical round of holes , under the condition of the same sample frequency , the differential values of velocities should tally with the actual measurement values of acceleration or be in the range of allowable error 摘要在同一測點同時布置了速度和加速度傳感器,在同一炮次中,在同樣的采樣頻率情況下,速度值求導應該與實測加速度相吻合或在誤差允許范圍內。
Feedrate planning of continuous micro - line ' s start and end points are discussed , and the constraining conditions , including the machine ' s acceleration and deceleration capability , allowable error of corner machining , maximum acceleration and dynamical behavior of the machine , are established 。 摘要針對連續小直線段高速高精插補算法中起始點和終止點的速度規劃,建立了包含機床加減速性能、轉接處誤差控制、最大加速度以及機床負載功率等的速度約束條件。
When the silicon technology comes to deep sub - micron level , the interconnect delay exceeds the gate delay ; and because of the increase of 1c work frequency , the allowable errors become smaller , and the influence of the transmission delay gets bigger , which increase the difficulty of the circuit design 在深亞微米制造技術中,芯片互連線延遲超過門延遲,而且隨著集成電路工作頻率的提高,允許的時序容差變小,傳輸延遲的影響加大,設計工作難度增加。